MATERIAL SAFETY DATA SHEET -----------------------------------------------------------------

 

PYROCHILL

aka

PYROCHILL SOLUTIONS

A product of SIPP International Industries, Inc.

A majority owned company of First Fidelity USA (Colorado)

 

December 29, 2019 PC-US Code NFPA

 

 

CHEMICAL FAMILY: Inorganic salts I.D. NUMBERS: 929002

 

NFPA RATINGS (Scale 0-4, U=Unrated): HEALTH=0 FIRE=0 REACTIVITY=0 HMIS RATINGS (Scale 0-4, where 4=severe hazard): HEALTH=1 FIRE=0 REACTIVITY=0

 

  • This product is labeled in accordance with regulations administered by the Consumer Product Safety Commission. The use pattern and exposure in the workplace are generally not consistent with those experienced by consumers.

     

  • The requirements of the Occupational Safety and Health Administration applicable to this Material Safety Data Sheet meets the requirements of the CPSC and as a result, this MSDS may contain additional health hazard information not pertinent to consumer use and not found on the product label.

     

  • HAZARDOUS INGREDIENTS INFORMATION COMPONENT: CAS# 1303-96-4 10 mg/m3 OSHA TWA 5 mg/m3 ACGIH TWA Carcinogen status of component: Not listed as a carcinogen by NTP, IARC, or OSHA. Non Toxic.

     

  • PHYSICAL AND CHEMICAL DATA DESCRIPTION: White, odorless, crystalline powder. BULK DENSITY: 48 lbs/cubic ft pH: 9.25 @ 20 °C (3% solution) MELTING POINT: 144 °F (62 °C) SOLUBILITY IN WATER: 5.8% @ 20 °C SOLVENT SOLUBILITY: Soluble in glycerol; very slightly soluble in alcohol; insoluble in acids.

     

  • FIRE AND EXPLOSION DATA FIRE AND EXPLOSION HAZARD - Product is not flammable, combustible or explosive.

     

  • FIRE FIGHTING MEDIA - Extinguish using agent suitable for type of surrounding fire. Product is fire retardant.

     

  • FIRE FIGHTING - No acute hazard.

     

  • HEALTH HAZARD DATA NOTE: The acute health effects described below are those which could potentially occur for the finished product. They are based on the toxicology information available for the finished product. Known chronic health effects related to exposure to a specific ingredient are indicated.

     

  • ACUTE HEALTH EFFECTS: INHALATION: Dust may cause mucous membrane irritation with coughing, dryness of the mouth and throat.

     

  • SKIN CONTACT: Non-irritating to intact skin. Absorption through large areas of damaged skin may produce symptoms similar to those following ingestion.

     

  • EYE CONTACT: Direct contact with powder or dusts may cause slight irritation with redness,

     

  • INGESTION: May cause gastrointestinal disturbances such as headache and or diarrhea.

     

  • CHRONIC HEALTH EFFECTS: No chronic health effects are expected from the intended use of these products or from foreseeable handling of them in the workplace. Moreover, a human study of occupational exposure to dusts showed no adverse effects.

     

  • MEDICAL CONDITIONS GENERALLY RECOGNIZED AS BEING AGGRAVATED BY EXPOSURE: Pre-existing skin conditions and respiratory illnesses (such as asthma).

     

  • EMERGENCY AND FIRST AID PROCEDURES FOR OVER INHALATION: Immediately remove from exposure area to fresh air.

     

  • SKIN CONTACT TO OPEN WOUNDS: Rinse affected area with soap or a mild detergent and plenty of water until no evidence of product remains.

     

  • EYE CONTACT: Immediately rinse eyes with plenty of water, occasionally lifting upper and lower lids, until no evidence of product remains. Get medical attention if pain or irritation occur.

     

  • INGESTION: Treat symptomatically and supportively. Maintain airway and respiration. If vomiting occurs, keep head in a position to prevent aspiration of vomitus. Dilution by rinsing the mouth and giving water or milk to drink is generally recommended.

 

 

REACTIVITY

 

  • REACTIVITY - Stable under normal temperatures and pressures.

     

  • INCOMPATIBILITIES: Strong oxidizers, acids, zirconium.

     

  • DECOMPOSITION - Thermal decomposition products may include oxides of sodium and boron.

     

  • POLYMERIZATION - Hazardous polymerization has not been reported to occur under normal temperatures and pressures.

     

  • STORAGE AND DISPOSAL Store away from incompatible substances. Store in a cool dry place. Keep container tightly closed when not in use. Observe all federal, state and local regulations when storing or disposing of this substance.

     

  • CONDITIONS TO AVOID Avoid generation of dust.

     

    SPILL AND LEAK PROCEDURES

     

  • OCCUPATIONAL SPILL - Sweep up and place in suitable clean, dry containers for reclamation or later disposal. Small residual amounts of material may be flushed with water to the sewer. Keep unnecessary people away.

     

  • OCCUPATIONAL PROTECTIVE EQUIPMENT VENTILATION - Provide local exhaust ventilation system to meet permissible exposure limits, where dusts are likely to be generated.

     

  • RESPIRATOR - Air contamination monitoring should be carried out in the manufacturing process of this product, where dusts are likely to be generated, to assure that the employees are not exposed to harmful concentrations the above permissible exposure limits. If respiratory protection is required, it must be based on the contamination levels found in the workplace, must not exceed the working limits of the respirator and be jointly approved by the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration (NIOSH-MSHA).

     

    FOR FIRE FIGHTING AND OTHER IMMEDIATELY DANGEROUS TO LIFE OR HEALTH CONDITIONS - Any self-contained breathing apparatus that has a full facepiece and is operated in a pressure-demand or other positive-pressure mode. Any supplied-air respirator that has a full facepiece and is operated in a pressure-demand or other positive-pressure mode in combination with an auxiliary self-contained breathing apparatus operated in pressuredemand or other positive-pressure mode.

     

  • CLOTHING - Protective (impervious) clothing is required where repeated or prolonged skin contact may occur.

     

  • GLOVES - Chemical-resistant gloves are required where repeated or prolonged skin contact may occur.

     

  • EYE PROTECTION - Dust-proof safety glasses are required to prevent eye contact where dusty conditions are anticipated.

     

     

  • REGULATORY INFORMATION MSDS DOT FLAMMABILITY CLASSIFICATION: Not applicable.

     

  • EPA - SARA TITLE III SECTION 313: Toxic chemicals - None. Biodegradable – Yes.

     

  • TSCA: All components of this product are listed or are exempted or excluded from listing on the U.S. Toxic Substances Control Act (TSCA) chemical substance inventory.

 

The information contained herein is provided in good faith and is believed to be correct as of the date hereof.

 

However, SIPP International Industries, Inc. and or its majority contrlled partner First Fidelity USA, Inc. makes no representation as to the comprehensiveness or accuracy of the information. It is expected that individuals receiving the information will exercise their independent judgment in determining its appropriateness for a particular purpose.

 

Accordingly, SIPP International Industries, Inc. and or First Fidelity USA, Inc. will not be responsible for damages of any kind resulting from the use of or reliance upon such information. No representations, or warranties, either expressed or implied of merchantability, fitness for a particular purpose or of any other nature are made hereunder with respect to the information set forth herein or to the product to which the information refers. MSDS CREATION DATE: 12/29/2019 SUPERSEDES: Rev. 1; REVISION DATE: 03/30/2015 REVISION: Due to the nature of this MSDS, hazardous ingredient information, physical and chemical data have been provided as to the scope of protection under the laws, rules and regulations regarding corporate trade secrets.

© 2020 by PYROCHILL SOLUTIONS a wholly owned division of FIRST FIDELITY USA, Inc. Colorado   For information call (855)797-6244

  • Facebook Social Icon
  • Twitter Social Icon
  • Instagram Social Icon